Stacking height doors: 1900 mm = 300 mm floor roller conveyor height + 1600 mm door stack
= 40 doors max.
At the infeed and outfeed side of the portal stacker protection boards will be used.
Production direction door: top edge of door in front seen in feed direction
Portal infeed with turning traverse by +/-90° for the handling of the parts in order to provide a length- and crosswise processing.
1. Throughfeed
Infeed of the doors lengthwise
Tenoning at length sides of the door
Outfeed of the doors lengthwise
Return guiding to the infeed
2. Throughfeed
Infeed of the doors crosswise (lay on turned by +90°)
Tenoning of the door top (lh side in the machine)
Outfeed of the doors crosswise (lay up turned by –90° = lengthwise)
Outfeed of the doors
Item 1:
Scissor Lift with above Mounted Roller Conveyor
(underneath the Portal Stacker)
consisting of:
Hydraulic scissors lift
Hydraulic including aggregate is near the floor frame of lifting table
Lifting table with integrated safety installations (switch ledges)
Geared roller conveyor set up onto the lifting table
2 Directions (for the outfeed and infeed of stacks)
Lifting table platform approx.
2600 x 1300 mm
Max. lifting capacity
1000 mm
Max. stack height
1600 mm
Max. stack weight approx.
4 metric tons
Infeed height
300 mm
Size of pit
without pit
Item 2:
Portal Stacker with horizontal Turning Device
The basic construction of the portal stacker consists of two lateral columns and the lay on traveling beams.
The portal carriage moves sideways on running tracks installed inside the traveling beams.
The end pieces of the portal columns carry the travelling gear drive and the guiding station for the toothed belt of the travelling carriage.
The carriage consists of a frame supported via running rolloers at the guide rails within the travelling beams.
The carriage receives all brackets/mountings and connections for the lifting column and the side duct compressor.
The lifting system flanged to the carriage is equipped with a turning device at its lower end and allows to turn the parts lengthwise and crosswise or vice versa.
Underneath the turning device a traverse is installed carrying the suction cross beams with the bellow suction cups which will be provided through a hose / tube system with the vaccum generated by the side duct compressor carried along with the carriage.
Overall length
10000 mm
Stacking height
300 / 1600 mm
Cycle capacity
Max. 4 cyles/min. with turning
Turning angle
90
Item 3:
Roller Conveyor with latereral Alignment
The fundamental construction of the roller conveyor consist of a rigid welded
frame made out of rectangular steel bars with adjustable feet for variable infeed height of +75/-25 mm.
Support roller diameter 90 mm standard incl. PVC coating, 5 mm thick.
Rollers equipped with chain sprockets 5/8”x3/8”.
Tangential chain driven through frequency converted geared motor fitted within the lower area of the basic frame.
The guiding chain runs in synthetic sliding rails across the length of the roller conveyor.
The tensioning of the chain is possible through regulating screws at the motor mounting.
The tangential chain drive from motor is completely covered with a protective sheathing.
Cross alignment of the v-belt with pneumatically actuated lifting.
V-belt guiding in a synthetic profile and driven via variable gear.
Length stop adjustable by oblong holes.
Pneumatically actuated head stop in front seen in feed direction.
Length:
3600 mm
Width:
2600 mm
Height approx.
Infeed of double end tenoner
Roller partition:
Approx. 200 mm
Quantity belt:
4 pieces
Item 4:
Floor Roller Conveyor
motorized
Height: 300 mm
Lenght: 2600 mm
Width: 1400 mm
Feed speed: 12 m/min (2 directions)
load capacity: 4 tons
Item 5:
Double End Tenoner
Fixed stop side on the left, movable side on the right.
consisting of:
basic machine
workpiece transport device
top pressure
width adjustment of the movable side
control NC 21
safety and protection facilities
Technical Data
- feed infinitely variable 10 - 40 m/min.
- workpiece overhang max. 110 mm
- workpiece thickness 8 - 90 mm
- working height up to upper chain surface 950 mm.
- working width double-sided min. 220 mm
- working width double-sided max. 2300 mm
- pneumatic connection 7-8 bar
13 x left 13 x right conveyor chain, rolling
13 x left 13 x right stepless stop cams
1 x left 1 x right steplessly adjustable stop cams automatic
1 x left 1 x right lifting device
1 x left 1 x right controlled top pressure
1 x left 1 x right line execution machine I or II
1 x left infeed fence 2500 mm long
2 x left 2 x right alignment station
1 x left panel taking-over device
1 x left 1 x right trimming column 1 guide
1 x left 1 x right prescoring unit 2,2 kw controlled, separate
1 x left 1 x right adjustment horizontal
1 x left 1 x right hogging unit 15 kw
1 x left 1 x right adjustment horizontal manual
1 x left 1 x right counter cut board
1 x left 1 x right trimming column 2 guides
1 x right trimming unit top and bottom 0,55 kw
2 x right pneumatic adjusting device for trimming motor
1 x right console for panel sizing part
1 x left hogging unit 8,1 kw for scoring from below, parallel rotating
1 x left pneumatic control
1 x left adjustment horizontal manual
1 x left adjustment vertical manual
1 x left hogging unit 15 kw
1 x left adjustment horizontal
1 x left adjustment vertical manual
1 x left trimming column 2 guides
1 x left standard trimming unit 4,5 kw for post-trimming of rebate
1 x left adjustment horizontal manual
1 x left adjustment vertical manual
1 x left standard trimming unit 4,5 kw for adding the rebate corner
1 x left adjustment horizontal manual
1 x right free space
1 x left electronic control
10 x left 10 x right extension - electronic control
1 x right electronic width adjustment
1 x left 1 x right electronic height adjustment
1 x left input NC 21
Item 6:
Roller Conveyor with controlled/selected Stops
- Technical description as per Item 3
Version without v-belt cross alignment, but with 2 pneumatically in and out swivelable stops in feed direction of the roller conveyor. Preselection of the swivel stops depending on the production direction of the unfinished door (door lengthwise or door crosswise).
Length:
3600 mm
Width:
2600 mm
Height:
Outfeed of the double end tenoner
Roller partition:
approx. 200 mm
Number of stops:
2 pieces
Item 7:
Portal Stacker with horizontal turning Device
The basic construction of the portal stacker consists of two lateral columns and the lay on traveling beams.
The portal carriage moves sideways on running tracks installed inside the traveling beams.
The end pieces of the portal columns carry the travelling gear drive and the guiding station for the toothed belt of the travelling carriage.
The carriage consists of a frame supported via running rolloers at the guide rails within the travelling beams.
The carriage receives all brackets/mountings and connections for the lifting column and the side duct compressor.
The lifting system flanged to the carriage is equipped with a turning device at its lower end and allows to turn the parts lengthwise and crosswise or vice versa.
Underneath the turning device a traverse is installed carrying the suction cross beams with the bellow suction cups which will be provided through a hose / tube system with the vaccum generated by the side duct compressor carried along with the carriage.
Overall length
10000 mm
Stacking height
300 / 1600 mm
Cycle capacity
Max. 4 cyles/min. with turning
Turning angle
90
Item 8:
Scissor Lift with above Mounted Roller Conveyor
(underneath the Portal Stacker)
consisting of:
Hydraulic scissors lift
Hydraulic including aggregate is near the floor frame of lifting table
Lifting table with integrated safety installations (switch ledges)
Geared roller conveyor set up onto the lifting table
2 Directions (for the outfeed and infeed of stacks)
Lifting table platform approx.
2600 x 1300 mm
Max. lifting capacity
1000 mm
Max. stack height
1600 mm
Max. stack weight approx.
4 metric tons
Infeed height
300 mm
Size of pit
without pit
Item 9:
Floor Roller Conveyor
motorized
Height: 300 mm
Lenght: 2600 mm
Width: 1400 mm
Feed speed: 12 m/min (2 directions)
load capacity: 4 tons
Item 10:
Intermediate Floor Roller Conveyors
3 pcs.
motorized
Height: 300 mm
Lenght: 3000 mm
Width: 1400 mm
Feed speed: 12 m/min (2 directions)
load capacity: 4 tons
